Super Pocket Bike Guide

A ugust 25, 2014

Pocket Bikes

Cagllari

GP MX3

Blade

Raptor

GP RS-R

RX1 Mini

KTX Dirt

Super Bikes

R32 S Bike

X18-R Nitro

X19-CR Dom

DBX-T Bikes

ZX1 X Bike

X7 Bullet

Mini ATVs

Apache ATV

T-Rex ATV

Scorpion ATV

Mini Quads

A4 Quad

Evo Quad

Cobra Quad

Bike Parts

Perf Package

Upgrades

Bike Parts 1

Bike Parts 2

Bike Parts 3

Safety Gear

Pocket Bike Info

Safety

Racing Bikes

Bike Usage

The Sport

Information

FAQs

Help

About Us

Mail Orders

Contact Us

QUICK-START GUIDE for POCKET BIKES

MUST READ BEFORE OPERATING YOUR NEW POCKET BIKE or MINI QUAD

What type of gas should I use?

What should the oil mixture be? How do I mix it?

How do I properly start the bike with the Pull Starter?

Chain Tension is CRUCIAL. How do I check & adjust the chain?

Engine will not stay on. How do I adjust the idle?

Bike wants to take off when idling. How do I adjust the idle?

How do I adjust the Speed Governor on my Pocket Bike?

How do I fill air in the tires? What is the correct PSI?

How long is the break-in period?

How long can these bikes be ridden continuously?

How long is the riding time per tank of gas?

I broke a part on my bike. How can I fix it?

How do I fix the exhaust if it is damaged?

Is the Fuel Filter necessary? How do I replace it?

Gas is leaking from the overflow tube. How do I stop it?

What type of gas should I use?

For best performance, use high octane gas from a local gas station. 91 - 93 octane premium

unleaded fuel is recommended. You may also use 87 octane gas as well. Do not use any type of

diesel fuel.

What should the oil mixture be? How do I mix it?

(This se ction only a pplie s to our 2-Strok e bik e s; 4-Strok e bik e s ne e d only pure ga soline )

The gas-to-oil mixture should be 50:1. Mixing the fuel is very easy and takes less than 1 minute.

Using the provided mixing bottle, pour the gas into the bottle to the specified line (up to the "576"

line) and pour 2-Stroke / 2-Cycle Small Engine Oil ( This type of oil is available at any auto parts

store. Do not use regular car oil ) to the designated line (up to the "600" line). Close the cap and

shake for 3 seconds. You are ready to fill the bike's gas tank with the mixture.

To sum this up, add Gasoline 1st and fill it to the "576" line. Then add a little bit of 2-stroke oil.

The oil will only top off the bottle from the "576" mark to the "600" mark.

How do I properly start the bike with the Pull Starter?

Below is the proper procedure to start your pocket bike via the Pull Start:

1. Stand the bike upright; you should be straddling the bike. The pull start cord is on your right

side.

2. Make sure the fuel petcock valve is in the vertical position ( the white valve lever should be

straight up and down ).

3. Put the choke lever in the closed position ( the metal lever in the UP position ).*

conve rte d by W e b2PDFC onve rt.com

4. Pull the start cord out slowly until it reaches its maximum length and then let it retract. Repeat

this procedure 2 times.**

5. On the 3rd attempt, pull the cord out swiftly with one strong pull.***

( pull the cord straight back; do not pull at an angle, as pulling it at an angle may damage the

cord ).

6. Repeat steps 4 and 5 until the bike starts.****

7. After the bike starts, let it warm up for 1 minute. Then put the choke lever to the open position (

metal lever down ).

8. The bike is now ready to ride.

* In certain weather conditions, you may put the choke lever in the middle position to help make it

easier to start.

** Starting may require several tries when the bike is still new. After break-in, the bike will start

...